成品万能支撑器厂家杭州比模特科技青龙棋牌官网主要经营喷泉景观支撑器,防腐木支撑器,木塑支撑器,水景支撑器等,提供万能支撑器安装与价格报价业务,若大家有万能支撑器、万能支撑架、地板支架或塑木龙骨支架的需要,请联系:0571-86221809

NEWS 新闻中心

NEWS CENTER

  • 万能支撑器的具体施工方案介绍
  • 本站编辑:杭州比模特科技青龙棋牌官网发布日期:2019-04-10 20:48 浏览次数:

一、先做好策划方案

先做好策划方案,以施工大样图和加工单为依据,熟悉了解各部位尺寸和做法,尤其落实好地面LED灯带及边角等部位之间的关系,避免收口处出现问题。

二、基层处理

处理好广场垫层上的杂物,保持地面相对平整,不要出现局部高低起伏现象,避免底基座底面不能够完全与地面相接触造成不稳,水泥地面哑光面即可。根据图纸的标示和石材厚度来确定万能支撑器高度,再通过万能支撑器的各个部件,左右旋转调节万能支撑器所需高度。但值得注意的是,千万不要将万能支撑器旋转的过于紧密,也不要旋出指示范围,按产品的使用方法操作,才能发挥出产品的最佳使用状态。

三、检查和控制支撑器位置

依据施工大样图及广场实际尺寸,在广场上拉十字控制线,弹在基层上,并引至墙面底部,然后找出面层标高,在墙上弹出水平标高线,同时弹出支撑器中心线,进行试排。把花岗岩石材排好,以便检查石材之间的缝隙,核对石材与墙面、灯带、洞口等部位的相对位置。

四、注意排水

可采用暗排水构造。基层为了排水方便一般具有一定坡度,但是完成面必须保持水平。例如,一工程结构基础为4%的坡度,要求完成面保持水平。

五、找好坡度

万能支撑器找坡范围1%~5%,控制坡度关键部件为调节件。施工时应首先将调节件上找坡调整到4%,再将找坡箭头中的4%调整指向找坡方向,然后整体铺装时按照先前调整好的找坡度依次展开。这样将完全抵消结构找坡带来的面层不平整问题,对于大面积石材铺贴施工中控制平整度具有很大的优势,精确度非常高。

六、留缝大小

留缝的作用一方面可以处理石材规格不整的问题,同时也是给排水、热胀冷缩预留位置。缝隙主要依靠调节件控制,可以依据实际需求选择调节件。调节件可严格控制留缝精度,消除人为因素,从而在外观上达到整齐划一的目的,提高美观效果,这也是有别于常规做法的优点之一。

七、检查平整度

首先任选一块石材,用水平尺按对角线的方向放下,检查是否平整,然后测定每2块上下左右相邻的石材,若平整则水平尺中间的水珠应该在中间。最后检查边角是否对直,从实际检验结果来看效果非常好。地面LED灯带的灯具依据石材高度定做,坐落在万能支撑器之上。灯具相关线缆、控制系统、电源等从底部架空层敷设,灯带面层与灯具相互独立。面层选用定制钢化玻璃,灯带两侧石材开槽以便安置玻璃,开槽规格为10mm,通过耐候胶将玻璃固定在两侧石材小槽上。这种做法一方面保证了灯带核心部件即灯具不受承压破坏,更重要的是便于检修,更换灯具、线缆等工作。

八、使用分割片

注意分割片的使用技巧。假如遇到特殊的安装情况,可以去掉若干分割片或者注意在不需要分隔的边角等部位使用;同样底座安装时遇到特殊情况也可以切除,例如支撑器底部附件有障碍物,进而影响面层石材铺贴的模数,在此情况下可适当切除相应部位。

九、利用垫片处理石材厚度不均的问题

石材在加工过程中往往存在着厚度不均的瑕疵。在安装石材过程中,万能支撑器可以通过垫片进行调节进而消除石材自身的误差。这就需要我们根据施工现场的具体情况和石材厚度相差的情况可自行增减垫片进行调整。


l2-1P62Q61542-50_267_210[1].jpg

First, plan the plan first
First, do a good planning plan, based on the construction sample map and the processing sheet, familiar with the size and practices of various parts, especially to implement the relationship between the ground LED light belt and other parts to avoid problems at the closing point.
Treatment at the grassroots level
Deal with the debris on the floor of the square, keep the ground relatively flat, do not appear local ups and downs, and avoid the bottom of the base can not completely contact the ground to cause instability, cement surface matte surface can be. According to the drawing marks and stone thickness to determine the height of the universal support, and then through the various components of the universal support, left and right rotation to adjust the universal support required height. However, it is worth noting that it is important not to rotate the universal support too closely, nor to rotate the indication range, according to the method of use of the product, in order to play the best use of the product.
III. Inspection and control of support positions
According to the construction sample map and the actual size of the square, pull the cross control line on the square, bomb it on the base, and lead it to the bottom of the wall. Then find the floor elevation, pop up the horizontal elevation line on the wall, and pop up the center of the support device. Line, test row. Arrange the granite stone in order to check the gap between the stone and check the relative position of the stone and the wall, lampstrip, hole and other parts.
Fourth, pay attention to drainage
Dark drainage structures can be used。 The basic level generally has a certain slope for the convenience of drainage, but the completion surface must be maintained at a level。 For example, an engineering structure is based on a slope of 4 %, requiring the completion surface to be maintained at a level。
Five, find a good slope
The range of the universal support is 1 % to 5 %, and the key part of the slope control is the adjusting part. During construction, the adjustment should first be adjusted to 4 % on the adjustment part, and then the 4 % adjustment in the search arrow should be pointed to the search direction, and then the overall paving should be carried out according to the previously adjusted search slope. This will completely offset the problem of uneven surface layer caused by the structural slope, which has great advantages and high accuracy for controlling the smoothness in the construction of large areas of stone paving.
Size of remaining seams
On the one hand, the function of the remaining seam can deal with the problem of incomplete stone specifications, and it is also reserved for water supply and drainage, hot expansion and cooling。 The gap mainly depends on the adjustment part control, can choose the adjustment part according to the actual demand。 The adjustment parts can strictly control the accuracy of the remaining seams and eliminate human factors, so as to achieve the goal of uniformity in appearance and improve the aesthetic effect。 This is also one of the advantages that is different from the usual practice。
VII. Inspection of smoothness
First of all, select a piece of stone, put it down in the diagonal direction with a horizontal ruler, check whether it is flat, and then determine the stone adjacent to each of the two blocks. If it is flat, the water ball in the middle of the horizontal ruler should be in the middle. Finally check whether the edge angle is straight, from the actual test results show that the effect is very good. The lamps of the LED light belt on the ground are customized according to the height of the stone and are located on the universal support device. Lamp related cables, control systems, power supply, etc. are laid from the bottom shelf layer, and the lamp surface layer and the lamp are independent of each other. The surface layer is made of custom tempered glass. The stone on both sides of the light belt is slotted to fit the glass. The slot specification is 10m. The glass is fixed on the small stone troughs on both sides through weather resistant glue. On the one hand, this approach ensures that the core parts of the lampstrip, namely, the lamps, are not damaged by pressure, and more importantly, it is easy to overhaul, replace lamps, cables, and other work.
VIII。 Use of fragmentation
Pay attention to the technique of splitting pieces. If you encounter a special installation situation, you can remove a number of partitions or pay attention to the need to separate the edges and other parts of the use; When the same base is installed, special conditions can also be removed. For example, there is an obstacle at the bottom of the support device, which in turn affects the modulus of the surface layer stone paving. In this case, the corresponding part can be appropriately removed.
Treatment of uneven thickness of stone using gaskets
Stone in the process of processing, there are often uneven thickness of the defects. In the process of installing stone, the universal support can be adjusted by the gasket to eliminate the error of the stone itself. This needs us according to the construction site and the concrete situation of stone thickness difference can increase or decrease pad adjustment.

Copyright 2018-2020 版权所有:杭州比模特科技青龙棋牌官网 All Right Reserved

盛京棋牌 盛京棋牌 彩客网 555彩票 盛京棋牌 555彩票 盛京棋牌 98彩票注册 盛京棋牌 彩客网