万能支撑器找坡范围１％～５％ ，控制坡度关 键部件为调节件。施工时应首先将调节件上找坡调整到４％ ，再将找坡箭头中的４％调整指向找坡方向，然后整体铺装时按照先前调整好的找坡度依次展开。这样将完全抵消结构找坡带来的面层不平整问题，对于大面积石材铺贴施工中控制平整度具有很大的优势，精确度非常高。
留缝的作用一方面可以处理石材规格不整的问题 ，同时也是给排水、热胀冷缩预留位置。缝隙主要依靠调节件控制，调节件分２、４、５、６、８、１０ ｍｍ共６个型号，依据实际需求选择调节件。调节件可严格控制留缝精度，消除人为因素，从而在外观上达到整齐划一的目的，提高美观效果，这也 是有别于常规做法的优点之一。
青龙棋牌官网 石材在加工过程中往往存在着厚度不均的瑕疵。在安装石材过程中，石材万能支撑器可以通过垫片进行调节进而消除石材自身的误差。如垫片规格分为１ｍｍ 及２ｍｍ 厚，根据石材厚度相差的情况可自行增减垫片进行调整。
The specific Shigongfangfa of the universal support can be subdivided into 9 steps:
First, plan the plan to use the construction sample map and the processing sheet as the basis, and be familiar with the size and practices of the various parts. In particular, implement the relationship between the surface Leld and the edges and other parts to avoid problems at the closing point.
2, grassroots treatment
Clean up the debris on the square cushion and brush off the mortar bonded to the cushion with a wire brush. The ground is required to be relatively flat, without local ups and downs, to avoid the bottom of the base can not completely contact the ground to cause instability, cement surface matte surface can be. The height of the universal support device is determined according to the elevation shown in the drawings and combined with the thickness of the stone. Then the required height can be adjusted by rotating each component to the left and right. Do not spin too closely, and do not spin out the indication range. The best use of the product can be achieved by using the arrow on the product.
3, check and control support position
According to the construction sample map and the actual size of the square, pull the cross control line on the square, bomb it on the base, and lead it to the bottom of the wall. Then find the floor elevation, pop up the horizontal elevation line on the wall, and pop up the center of the support device. Line, test row. Arrange the granite stone in order to check the gap between the stone and check the relative position of the stone and the wall, lampstrip, hole and other parts.
Dark drainage structures can be used。 The basic level generally has a certain slope for the convenience of drainage, but the completion surface must be maintained at a level。 For example, an engineering structure is based on a slope of 4 inches, requiring the completion surface to be maintained at a level。
5, looking for a slope
The universal support finds the slope range of 1 <UNK> ~ 5 <UNK>, and the control slope key off part is the adjusting part. During construction, the adjustment shall first be adjusted to 4 points on the adjustment part, and then the 4 points in the search arrow shall be adjusted to the search direction, and then the overall paving shall be carried out in order to follow the previously adjusted search slope. This will completely offset the problem of uneven surface layer caused by the structural slope, which has great advantages and high accuracy for controlling the smoothness in the construction of large areas of stone paving.
6, leave seam
On the one hand, the function of the remaining seam can deal with the problem of incomplete stone specifications, and it is also reserved for water supply and drainage, hot expansion and cooling. The gap mainly depends on the adjustment part control, the adjustment part is divided into 2, 4, 5, 6, 8, 10m a total of 6 models, according to actual needs selected adjustment parts. The adjustment parts can strictly control the accuracy of the remaining seams and eliminate human factors, so as to achieve the goal of uniformity in appearance and improve the aesthetic effect. This is also one of the advantages that is different from the usual practice.
7, flatness inspection
First of all, select a piece of stone, put it down in the diagonal direction with a horizontal ruler, check whether it is flat, and then determine the stone adjacent to each of the two blocks. If it is flat, the water ball in the middle of the horizontal ruler should be in the middle. Finally check whether the edge angle is straight, from the actual test results show that the effect is very good. The lamps on the LED light belt on the ground are customized according to the height of the stone and are located on the universal support device. Lamp related cables, control systems, power supply, etc. are laid from the bottom shelf layer, and the lamp surface layer and the lamp are independent of each other. The surface layer is made of custom tempered glass, and the stone on both sides of the light belt is slotted to fit the glass. The slot specification is 10mm. The glass is fixed to the small stone troughs on both sides through weather resistant glue. On the one hand, this approach ensures that the core parts of the lampstrip, namely, the lamps, are not damaged by pressure, and more importantly, it is easy to overhaul, replace lamps, cables, and other work.
8, the use of separators
There are some application techniques when using, such as four separators with a width of 10m wide, in which several separators can be removed for special installation situations, for example, in parts such as edges that do not require separation; When the same base is installed, special conditions can also be removed. For example, there is an obstacle at the bottom of the support device, which in turn affects the modulus of the surface layer stone paving. In this case, the corresponding part can be appropriately removed.
9, the treatment of stone thickness uneven
Stone in the process of processing, there are often uneven thickness of the defects。 In the process of installing stone, the stone universal support can be adjusted by the gasket to eliminate the error of the stone itself。 If the gasket specification is divided into 1M M and 2m thick, according to the difference in the thickness of the stone, the gasket can be adjusted by itself。